Сервис обратного звонка RedConnect

+38 (067) 828 80 08

+38 (044) 392 06 05

Features
Technical specifications
  • Reverse mode
    RC-S — no
    RC-D — yes
  • Power supply, V
    3×380+N
  • Power frequency, Hz
    50±1
  • Rectifier rated output voltage when operate without galvanic isolation of current and voltage sensors (can switch), V
    6; 12; 24; 48
  • Rectifier rated output voltage when operate with galvanic isolation board module of current and voltage sensors, V
    Up to 540
  • Static error of the output voltage/current stabilization
    No
  • Analog reference, V
    0 to 10 (or ±10)
  • Number of analog reference inputs
    2
  • ADC resolution, bits
    12
  • Input voltage from current sensor, mV
    ±60, ±75
  • Rectifier control system
    Digital, microcontroller
  • Operation mode setting (stabilization of current and voltage, regulation of the opening angle, reversing of the rectifier polarity)
    External digital inputs, RS-485 interface
  • Select of the rectification circuit and other settings
    DIP-switch on the control board
  • Fine-tuning of the control range, coefficients of the PI-controller, initial and final regulation angles
    Variable resistors on control board
  • Number of the rectifier temperature sensors
    2
  • Indication of the control modes and faults
    LED indicator connected to discrete outputs of control unit, or can use RS-485 interface
  • Protection standart
    IP56
  • Dimensions (H×W×D), mm
    200×250×100
Description of the device
The Thyristor Rectifier Control Device available in two versions: RC-S is to control one group of thyristors (non-reversible rectifier), RC-D is to control two groups of thyristors (reversible rectifier).
The models, RC-SL and RC-DL are designed for work in converters with output voltages 6, 12, 24 and 48 volts, using of power step-down transformer connected between power supply and rectifier bridge. For work in converters with higher output voltages, it is necessary to use control units, RC-SH and RC-DH, with galvanic isolation module of the output voltage/current sensor. Device is designed as form of block in a sealed plastic box, and allow to operate in wet and aggressive conditions of galvanic facilities.
All external connections of unit are demountable and do not require soldering, which make installation more simple and reduce time of the device commissioning.
Device has a protection system with an indication on the external connected LED indicators. When protection is activated, corresponding digital output switches on which can also be used to monitor the status of the rectifier by the control device of the upper rank.
Device has a protection system with an indication on the external connected LED indicators. When protection activated, corresponding digital output which can also be used to monitor the status of the rectifier by the control device of the upper rank.
It is also possible to connect a remote control: analog or digital via the interface RS-485 - as well as to build a network of the isolated interface RS-485 for controlling and monitoring the rectifiers group.
Typical applications
  • Production and modernization of existing rectifiers for galvanizing lines
  • Electrochemical metalworking machines
  • Using in airfield start-charging rectifier with 28 V output voltage
  • Power control of three-phase heaters and other processes with RMS value regulation of output voltage
Technical Support
  • Qualified experts are available to provide consultation on application, installation, setting and exploitation.
  • The selection of technical options according to your needs.
  • Design of automation systems with equipment.
Production and Delivery
  • The control unit is supplied from our warehouse in Ukraine.
  • If the required models are not available, they can be delivered upon request.
  • If the customer has any specific requirement for the equipment, control units can be produced upon the request.
Service and Warranity
  • Warranty and post-warranty service of products
  • 18 months warranty

© 2010–2017

"Diada Group" LLC

E-mail: info@diadagroup.com

Office:

01133, Ukraine, Kyiv, 34, Lesya Ukrainka blvd., off. 213

Tel.: +38 (067) 828-80-08, +38 (044) 229-08-08

Manufacture:

03057, Ukraine, Kyiv, 3, Oleksandra Dovzhenko Street, 2nd floor

Tel: +38 (044) 392-06-05, +38 (098) 105-60-71