Сервис обратного звонка RedConnect

+38 (067) 828 80 08

+38 (044) 392 06 05

December 12, 2016
The updated software version of the thyristor rectifier control unit model RC-S and RC-D.
Added function of control on protocol Modbus RTU (RS-485). This allows to control the unit with the programmable logic controller (PLC) and combine control units into the network.

Available functions of mode selection , reverse control, setting output current or voltage to obtain current measurements values, status monitoring and diagnosis of problems, reading the state of discrete inputs and control of discrete outputs.
November 18, 2016
Novel servodrives model XDC-201.
Servodrives model XDC-201 are the small-size version of servo series XDC-200.

Compact four-quadrant servodrives DC XDC-201 are designed to work with low-voltage DC motors in speed, position and torque control modes with feedback via tachogenerator, encoder or without external feedback.

Servo XDC-201 used in designing or upgrading of servo-systems, which is important for high performance, compact size and low cost.

More details about the new model.
November 01, 2016
We are participating in the exhibition.
XV INTERNATIONAL INDUSTRIAL FORUM '2016
November 22-25, 2016


Dear colleagues and partners! The "Diada Group" company will take part in the XV INTERNATIONAL INDUSTRIAL FORUM '2016, which will be held from 22 to 25 of November 2016 at "International Exhibition Centre": Ukraine, Kyiv, Brovarsky Ave, 15, "Livoberezhna" underground station.

We invite you to visit our stand.
You can get professional consultation from our experts, look at our full range of products and mace an order!

Visitor registration:
All visitors pass obligatory free registration.

Entrance to the exhibition, all the days of work is carried out only by badges.

Additional information ― on the organizers site.
April 22, 2016
The soft starter devices of SSB-21 series are developed.
This an economical solution for the effective start-up, protection and braking of the three-phase asynchronous motors.

Starting device of SSB-21 series allows to get rid of:
  • drawdowns voltage and current surges, arise because of direct start of asynchronous motor;
  • water hammer and pressure surges in the pipes at the start and stop of the pump;
  • mechanical overloads that lead to the need for frequent maintenance and repair.
More details about the device
October 27, 2015
We are participating in the exhibition.
XIV INTERNATIONAL INDUSTRIAL FORUM '2015
November 24 - 27, 2015


Dear colleagues and partners! The "Diada Group" company will take part in the XIV INTERNATIONAL INDUSTRIAL FORUM '2015, which will be held from 24 to 27 of November, 2015 at "International Exhibition Centre": Ukraine, Kyiv, Brovarsky Ave, 15, "Livoberezhna" underground station.

Visitor registration:
All visitors pass obligatory free registration.

Entrance to the exhibition, all the days of work is carried out only by badges.

Additional information ― on the organizers site.

We will be glad to meet you at the show!

You can get professional consultation from our experts, look at our full range of products and mace an order!
March 19, 2015
Thyristor Rectifier Control Unit Models (RC-S and RC-D) have been developed.
The unit is designed to control a reversible / irreversible controlled three-phase thyristor rectifier in the current and voltage stabilization modes and to control the triggering angle with the linearization of the regulation characteristics, as well as for the power control of three-phase heaters and other processes which need the regulation of the effective value of the output voltage. More information about the control unit.
March 10, 2015
New models of the Servo Converter XDC-100 have been developed.
New models of XDC-110, XDC-120 and XDC-130 have been released. The new models are one-quadrant (Irreversible) and they have four control modes:
  • Speed control mode with a tachogenerator.
  • Speed control mode with the compensation of losses in the rotor circuit (I*R).
  • Torque control mode.
  • Electric drive excitation current control mode.
The last mode is intended for the construction of the two-zone electric drive when working in conjunction with the servo сonverter armature circuit (for example, XDC 200 series or any other). This mode provides stabilization of the electric drive excitation current when operating in the first zone and a transition to the second zone when the armature voltage reaches the nominal value. The Servo Converters have a design and dimensions similar to the Servo Converters XDC 200 Series. More information about the new models.
13 february 2015
We are participating in the exhibition.
XIX International exhibition Elcom Ukraine
21.04.2015 – 24.04.2015


Dear colleagues and partners! The "Diada Group" company will take part in the XIX International exhibition Elcom Ukraine, which will be held from 21 to 24 of April, 2015 in st. Salyutna, 2-B, Kyiv 04111, Ukraine, exhibition center "Kyiv ExpoPlaza" (metro station "Nyvky").

Exhibition opening hours:
21.04.2015 ― from 10:00 till 18:00.
22.04.2015 ― from 10:00 till 18:00.
23.04.2015 ― from 10:00 till 18:00.
24.04.2015 ― from 10:00 till 17:30.

Visitor registration:
All visitors pass obligatory free registration.

Entrance to the exhibition, all the days of work is carried out only by badges.

Additional information ― www.elcom.ua.

We will be glad to meet you at the show! We are waiting for you in Hall # 1.

You can get professional consultation from our experts, look at our full range of products and mace an order!
07 february 2014
The new model of Servo amplifier of direct current XDC-230 series was released
This model is a more powerful version of Servo amplifier XDC series.
The range of rated output current increased to 75A . The range of working voltage is increased to 400V, that allows you to connect Servo amplifier to a three-phase industrial network and work with electric motors of direct current with a rated voltage of the anchor to 400V.
Also added function of limiting the maximum acting output voltage value twice, allowing you to use motors with a rated voltage of the anchor to 220 V, in a three-phase power transformer from 400V mains voltage without a matching transformer.
More about Servo Amplifier of direct current XDC-230 series
31 january 2014
The new software version added intensity adjuster while working with Analog task.
This allows to use servo amplifier in cases where you need a smooth increase in speed and smooth braking of the mechanisms, such as electric drive of the universal lathes and milling machines, electric drive of the molding machines, drive of the printing equipment and rewinding machines.
Intensity adjuster working in the speed and torque control modes. The intensity of acceleration installed a 16- way switch SW2. When setting this switcher to " 0" the intensity of the acceleration of the motor is maximum. Setting the switcher to «F» corresponds to the set of smooth speed.
14 november 2013
An updated version of Servo amplifier XDC series was released
The updated version of the Servo amplifier XDC series added the following modes: speed control with usage of the encoder, as the feedback device, the position mode with signals control Pulse + / Pulse-(CW, CCW). Also added new types of protection: protection against over voltage on the DC bus and the control circuit integrity of the bit key.
17 june 2013
Updated information on the website
An updated version of our website - see detailed description of DC servo amplifier XDC-2101 series describing its mode of operation and usage, added technical information for Servo motor series SZD.

© 2010–2017

"Diada Group" LLC

E-mail: info@diadagroup.com

Office:

01133, Ukraine, Kyiv, 34, Lesya Ukrainka blvd., off. 213

Tel.: +38 (067) 828-80-08, +38 (044) 229-08-08

Manufacture:

03057, Ukraine, Kyiv, 3, Oleksandra Dovzhenko Street, 2nd floor

Tel: +38 (044) 392-06-05, +38 (098) 105-60-71